Tag Archives: primer



We usually want the most velocity we can SAFELY get, and here’s all about how to stay safe. Keep reading!

Glen Zediker

I’ve been on the topic of load development — “working up” a load — for the past couple of editions, and, based on the excellent feedback from you all, here’s more. As always, there’s only so much I can write before I have to cut myself off.

I’ve said that velocity is the initial leading indicator of pressure. Velocity, in itself, however, is not a definitive indicator of pressure. I’d like to clarify… The first point is that I am a big believer in establishing a goal for load development, and, for me (and likely most others) that is a velocity. Accuracy is a given! I will never consider a combination that’s not shooting little knots downrange, but accuracy and velocity are not mutually exclusive. I also would never consider a combination that produced very small groups at an unacceptably low velocity, and that’s because I’m shooting (always) beyond 200 yards. The super-accurate low-velocity load gets its bullet shifted that much more in a variable wind, so it’s way on less likely to maintain those small groups.

I want to hit the velocity ballpark I have in mind and that’s why chronograph readings as I’m incrementally increasing the propellant charge are my leading indicator to how close I’m getting. I am also, always, looking for pressure signs on the spent cases — each and every one ejected.

So about those pressure signs…

Primer condition gets first attention.

primer pressure signs
Middle is what I want to see: pretty much a new primer with a nice round dimple in the center. Right, well. Massive pressure! But notice that the primer still shows a radius on the edges and is only a little rougher in appearance, well, aside from the crack…

A primer should have a smoothly dimpled firing pin indention, a shiny appearance, and a visible radius on its edge. If any of those are missing or compromised to varying degrees, there’s your sign… A dull and flattened primer has been abused, as well as one with a pitted or cratered appearance. Clearly, a crack or leak (indicated by black fouling) is way over the limit. After experience, backed up by gauged measurements, you’re liable to find that judging what’s “normal” and “safe” from one rifle can be different from another. I have had individual guns that flattened primers at any point near a safe-maximum charge. And, I’ve had them that just lied. Unfortunately, small-rifle primers don’t show always show pressure signs as reliably as large-rifle primers (structural differences). I’ve had experiences where the primers are all nice and shiny like and then blow out with the next increment. Shame on me for taking it there, and, speaking of: don’t get greedy! That’s one reason a velocity goal is important. Despite what your kindergarten teacher told you, you’re not that special… If you’re reading another 50+ feet per second more than what consensus says you should, better bet you’re over-pressure. “We” went through a lot of that when coated bullets got popular: those changed all the rules for “maximums.”

flattened primer
Here’s flat. My experience has been that large-rifle primers tend to display this indication more so than small. What’s happened is that the primer has flowed quite forcibly to fit the confines of its pocket and the bolt face. It’s also normal for some rifles, but that just means you have to know: pay attention and back off if you see a flattened primer.

The best pressure indicators show at the loading bench.

primer seating
My best “gage” for pressure is seating a primer in a fired and resized case. It’s a feel, gained through comparative experience, but too easy means there was too much pressure.

The reason I suggest (strongly) doing load work-up with new cases is because you then have a baseline. Measure the case head diameter (on the case, not the rim or groove) on the new case and compare it to the fired case. Up to 0.0005 (that’s ten-thousandths) is really high but some say acceptable (not me), and 0.0002-0.0003 is what I’d prefer. Plus, since a new case is at its smallest, meaning it will have a little less capacity than a fired case, you’re getting some assurance that the pressure will likely be a little lower from the same load in subsequent reuses of that case.

All dimensions are at their minimum in a new case. Primer pocket expansion is related to case head expansion. I get (what’s proven to be) a very accurate indication of pressure based on the resistance to seating a primer in that resized case. You have to use a priming tool that gives adequate feedback (meaning low leverage) but if the primer just slips right back in, that load was over-pressure. In a more extreme circumstance, the primer won’t stay seated. Yes. I have seen that. Shame on me, again.

Finally, a new case easily points out the difference between a “pressure ring” and a “sizing line” that can show just above the case head along the case body. A bright ring there indicates excessive stretching (a sizing line comes from the die reducing that area, and is perfectly normal). That “pressure ring” sign is also likely an “improper headspace” sign, but that’s another article.

pressure ring
Here’s a “pressure ring.” This poor old fellah used to be a brand-new Lake City Match case. I suspect there was some issue with this rifle’s headspace, but if you see this bright stretch mark, red flag it! It means the case is going to crack right there next use (called an “insipient head separation”).

Pierced Primers
This is a common malady on AR-platform guns, and especially on the big-chassis versions (SR-25, AR-10, and similar). Pressure both isn’t and is the culprit and the solution. Lemmeesplain: What causes the pierce is a firing pin hole that is too large. It is not the fit of the firing pin tip to the hole! An engineer can explain it, but it has to do with surface area covered by the firing pin hole, and then along with it the surface area of the primer. Simply: the firing pin hole turns into a cookie cutter. A primer pierce creates all manner of ills, including wrecked firing pins, gas flow through the charging handle area (where your face is), and abrasive debris scattered throughout the lower interior, including the trigger parts.

firing pin hole size
Blueprints call for a 0.058-inch diameter firing pin hole on an AR15 bolt. If the hole is too large then primer structural failures (pierces) will, not can, rear up. Too big is anything more than 0.062 inches, and I’ve seen plenty bigger than that. I use machinist’s drill bits to quick-check bolts: 1/16 (0.0625) and #53 (0.0595). If the first fits the hole, find another bolt. If the #53 won’t go, use that bolt with confidence.
pierced primer
Notice that this primer doesn’t really show excessive pressure signs. Just has a hole in it…

Excessive pressure gets blamed for a pierce but what’s really going on there is that it’s not certain that amount of pressure would be judged as “excessive.” It’s just gotten high enough to bring on this result. So, yes, lightening the load will stop the piercing, but, in my experience and that of many others, the pierces can start happening before reaching what most might agree on is a max load. I say that because “we” are all shooting about the same bullet/primer/case/propellant combinations in NRA High Power Rifle (with respect to Service Rifle division AR15s, for instance). Seeing pierced primers before hitting the proximity of competitive velocities points to “something else,” and that is the firing pin hole.

In a truly over-pressure load, the primer can crack or blow slap out, but it won’t pierce.

The information in this article is from Glen’s newest book, Top-Grade Ammo, available HERE at Midsouth. Also check HERE for more information about this and other publications from Zediker Publishing.